Line Hunting Sensor Module

Varenummer: 128-723
Varekode: KY-033
99 stk. på lager
Bestil nu for afsendelse mandag d. 23/11
Yderligere 105 stk. kan skaffes fredag d. 18/12
Vis lignende produkter i kategorien "Arduino"

Details

- Photosensitive diode
- Working power: + 5V
- Working current: < 10mA
- Working temperature range: 0'C 50'C
- Output electrical level signal: TTL
- Output interface: 3 wire
- Easy to install

 

PINOUT
PIN DESCRIPTION
1 GND
2 OUT
3 VCC (+5V)

 

 

EXAMPLE CODE


ARD_Line_Hunting_Sensor_HCARDU0005_Example.pde

 
 /* FILE:    ARD_Line_Hunting_Sensor_HCARDU0005_Example.pde    DATE:    03/07/12    VERSION: 0.1 This is a simple example of how to use the HobbyComponents Arduino Line hunting sensor module (HCARDU0005). It is a very simple module that requires only one DIO pin (defined as an input) to operate. When the sensor detects a reflective object  in close proximity it will pull a DIO pin that it has been connected to LOW. A  non reflective or no object in close proximity will cause the DIO pin to go high. You may copy, alter and reuse this code in any way you like but please leave  reference to HobbyComponents.com in your comments if you redistribute this code. */ /* Define the DIO pin that will be used to communicate with the sensor */ #define LINEHUNTSENS_DIO 2 /* Initialise serial and DIO */ void setup() {   /* Setup the serial port for displaying the status of the sensor */   Serial.begin(9600);      /* Configure the DIO pin the sensor will be connected to as an input */   pinMode(LINEHUNTSENS_DIO, INPUT); } /* Main program loop */ void loop() {   /* If the DIO pin is pulled low then an object has been detected */   if (!digitalRead(LINEHUNTSENS_DIO))     Serial.println("Object detected !");      }       
Inkl. moms
Kr. 39,00

Line Hunting Sensor Module

128-723
/ KY-033
99 stk. på lager
Bestil nu for afsendelse mandag d. 23/11
Ved bestilling nu, får vi dem hjem fredag d. 18/12

Details

- Photosensitive diode
- Working power: + 5V
- Working current: < 10mA
- Working temperature range: 0'C 50'C
- Output electrical level signal: TTL
- Output interface: 3 wire
- Easy to install

 

PINOUT
PIN DESCRIPTION
1 GND
2 OUT
3 VCC (+5V)

 

 

EXAMPLE CODE


ARD_Line_Hunting_Sensor_HCARDU0005_Example.pde

 
 /* FILE:    ARD_Line_Hunting_Sensor_HCARDU0005_Example.pde    DATE:    03/07/12    VERSION: 0.1 This is a simple example of how to use the HobbyComponents Arduino Line hunting sensor module (HCARDU0005). It is a very simple module that requires only one DIO pin (defined as an input) to operate. When the sensor detects a reflective object  in close proximity it will pull a DIO pin that it has been connected to LOW. A  non reflective or no object in close proximity will cause the DIO pin to go high. You may copy, alter and reuse this code in any way you like but please leave  reference to HobbyComponents.com in your comments if you redistribute this code. */ /* Define the DIO pin that will be used to communicate with the sensor */ #define LINEHUNTSENS_DIO 2 /* Initialise serial and DIO */ void setup() {   /* Setup the serial port for displaying the status of the sensor */   Serial.begin(9600);      /* Configure the DIO pin the sensor will be connected to as an input */   pinMode(LINEHUNTSENS_DIO, INPUT); } /* Main program loop */ void loop() {   /* If the DIO pin is pulled low then an object has been detected */   if (!digitalRead(LINEHUNTSENS_DIO))     Serial.println("Object detected !");      }